Technical Guide

Type II Sulfuric Acid Anodizing

Under MIL-A-8625, Type II refers to conventional sulfuric acid anodizing — the most widely used anodizing process in the aluminum industry. This guide covers specifications, process parameters, and why Type II is the ideal process for continuous coil anodizing.

MIL-A-8625 Standard 1.8–25 μm Thickness Class 1 & Class 2 Room Temperature Process
Jump to:
Definition

What Type II Means Under MIL-A-8625


Under the MIL-A-8625 military specification, Type II designates conventional sulfuric acid anodizing — the most common anodizing process used across the aluminum industry. It produces a porous aluminum oxide coating by electrolytically oxidizing the aluminum surface in a sulfuric acid electrolyte at or near room temperature.

The resulting oxide layer is integral to the aluminum substrate — it grows from the metal itself, not applied on top. This gives Type II coatings excellent adhesion, hardness, and corrosion resistance. The porous structure can be dyed to produce a wide range of decorative colors and then sealed for long-term durability. ALBEI's anodized aluminum products are manufactured using this exact process in a continuous coil-to-coil format at our production facility, held to rigorous quality standards.

When a spec sheet calls out "MIL-A-8625 Type II Class 2," it means a conventionally sulfuric-acid-anodized, dyed (colored) coating within the 1.8–25 μm thickness range.
Specifications

Type II Process Parameters


The defining characteristics of the Type II sulfuric acid anodizing process — from bath chemistry to coating thickness and applicable alloy families.

Process Bath
Sulfuric Acid
Coating Thickness
1.8–25.4 μm (0.00007"–0.001")
Typical Bath Temp
~20°C (68°F)
Voltage
12–20 V
Classes
Class 1 (Clear) / Class 2 (Dyed)
Common Alloys
1xxx, 3xxx, 5xxx, 6xxx Series
MIL-A-8625 Types

How Type II Compares to Other Anodizing Types


The MIL-A-8625 specification defines multiple anodizing types. Here is how Type II (conventional sulfuric acid) compares to the others — and why it has become the industry standard.

Type I — Chromic Acid
Uses chromic acid electrolyte. Produces thin coatings (2–10 μm) with limited color options. Chromic acid is environmentally restricted and increasingly phased out due to Cr(VI) toxicity concerns. Lower corrosion resistance than Type II at comparable thickness.
Type II — Sulfuric Acid
Uses widely available sulfuric acid. Produces thicker coatings (1.8–25 μm) with excellent dyeability for a full color range. Environmentally manageable, energy-efficient at room temperature, and capable of high-volume continuous production.
Type IIB — Thin Sulfuric
A thinner variant of sulfuric acid anodizing producing coatings under 4 μm. While faster to process, the minimal thickness provides limited corrosion protection and reduced color depth — insufficient for demanding architectural or outdoor applications.
Type II — Conventional Sulfuric
Full-thickness sulfuric acid anodizing (1.8–25 μm) delivers robust corrosion resistance, deeper and more durable color, and a wider performance envelope — suitable for everything from decorative interiors to architectural exteriors.
Type III — Hard Anodize
Produces very thick coatings (25–100+ μm) for maximum wear and abrasion resistance. However, it requires near-freezing bath temperatures (~0°C) with high current densities, making it energy-intensive, slow, and impractical for continuous coil processing. Excessive thickness can also cause brittleness and cracking during forming.
Type II — Conventional Sulfuric
Moderate film thickness (1.8–25 μm) is compatible with post-anodizing forming operations like bending and stamping. Runs at room temperature with lower energy costs, faster throughput, and is fully compatible with continuous coil-to-coil production lines.
Summary
Type I is environmentally restricted. Type IIB is too thin for durability. Type III is too thick, too cold, and too slow for coil. None offers the balance of performance, cost, and producibility needed for high-volume decorative and architectural aluminum.
Why Type II Is the Standard
Type II delivers the optimal balance of corrosion protection, decorative color flexibility, moderate film thickness, room-temperature processing, and low cost — making it the default choice for the vast majority of anodized aluminum applications worldwide.
Appearance Classes

Type II Classes: Clear vs Dyed


MIL-A-8625 defines two appearance classes under Type II. Class 1 is non-dyed (clear), Class 2 is dyed (colored). Both produce the same protective oxide layer — the difference is purely in the final appearance.

Class 1

Non-Dyed / Clear Finish

The anodic oxide is left in its natural state without dye application. The result is a clear, transparent coating that reveals the natural metallic appearance of the aluminum substrate — a clean, bright, silver-toned finish. Used when no color is needed or when the natural aluminum look is the design intent.

Clear Natural Silver No Dye Applied
Class 2

Dyed / Colored Finish

The porous oxide layer is immersed in organic or inorganic dyes after anodizing and before sealing. The dye molecules penetrate the pore structure, producing rich, durable color. Available in a wide palette of standard and custom shades for decorative and architectural applications.

Black Bronze Champagne Gold Red Blue Custom Shades
Application

Why Type II Is the Right Process for Coil Anodizing


Continuous coil anodizing is a high-volume manufacturing process where aluminum coil is fed continuously through a series of treatment tanks — cleaning, anodizing, dyeing, and sealing — in a single uninterrupted line. The process demands stable, repeatable bath conditions, moderate film thickness, and excellent color capability. Type II sulfuric acid anodizing meets every one of these requirements, which is why it is the process ALBEI uses for all of its continuous coil anodized products manufactured at our production facility.

01

Bath conditions suit continuous processing

Type II runs at 12–20V, 18–25°C with 15–20% sulfuric acid electrolyte — moderate, stable conditions a continuous line can maintain. Unlike Type III (hard anodize), which requires near-freezing baths (~0°C), Type II operates at room temperature, making it fully compatible with high-speed coil-to-coil production.

02

Film thickness matches coil needs

Type II produces a porous oxide film of 1.8–25 μm — the sweet spot for coil applications. A 10–25 μm layer provides strong corrosion protection and color retention without excessive thickness that could cause cracking during subsequent bending, stamping, or forming operations.

03

Excellent dyeability for decorative color

The porous structure accepts dyes readily and seals well, giving coil producers a wide color palette — clear, black, bronze, gold, red, blue, and custom shades. This allows a single coil line to serve diverse markets from architectural facades to consumer electronics.

04

Corrosion resistance for demanding environments

When properly sealed, Type II coatings withstand hundreds of hours of salt spray (ASTM B117), suitable for outdoor, marine, and industrial applications. This durability is backed by ALBEI's ISO 9001 and SGS certifications, ensuring consistent quality at scale.

05

Cost-effectiveness at volume

Sulfuric acid is inexpensive, the process is energy-efficient at room temperature, and continuous coil format minimizes labor and handling. This combination delivers the lowest cost per square meter of any anodizing process — critical for high-volume architectural and industrial applications.

Coil Suitability Comparison

Factor
Bath Temperature
Type II (Sulfuric)
18–25°C
Type I (Chromic)
35–40°C
Factor
Film Thickness
Type II (Sulfuric)
1.8–25 μm
Type I (Chromic)
2–10 μm
Factor
Colorability
Type II (Sulfuric)
Excellent
Type I (Chromic)
Limited
Factor
Cost
Type II (Sulfuric)
Low
Type I (Chromic)
Moderate
Factor
Coil Suitability
Type II (Sulfuric)
Ideal
Type I (Chromic)
Too thin
vs. Type III (Hard)
Bath Temperature
Type II (Sulfuric)
18–25°C
Type III (Hard)
~0°C
vs. Type III (Hard)
Film Thickness
Type II (Sulfuric)
1.8–25 μm
Type III (Hard)
25–100+ μm
vs. Type III (Hard)
Colorability
Type II (Sulfuric)
Excellent
Type III (Hard)
Limited
vs. Type III (Hard)
Cost
Type II (Sulfuric)
Low
Type III (Hard)
High
vs. Type III (Hard)
Coil Suitability
Type II (Sulfuric)
Ideal
Type III (Hard)
Too thick
Type II delivers the best balance of corrosion protection, decorative color flexibility, moderate film thickness compatible with post-anodizing forming, and low cost at high volume — all under stable, room-temperature bath conditions.
FAQ

Frequently Asked Questions


Common questions about Type II sulfuric acid anodizing and its application in continuous coil production.

What is Type II anodizing?
Type II is conventional sulfuric acid anodizing per MIL-A-8625. It produces an oxide layer of 1.8–25 μm on aluminum surfaces, providing corrosion protection and decorative coloring capability. It is the most widely used anodizing process in the aluminum industry.
What's the difference between Type II and Type III anodizing?
Type II uses sulfuric acid at room temperature producing 1.8–25 μm coatings. Type III (hard anodize) uses the same electrolyte but at near-freezing temperatures (0°C) with higher current densities, producing much thicker 25–100+ μm coatings for wear resistance. Type III is suitable for components requiring maximum surface hardness, while Type II is preferred for decorative and corrosion-protection applications at high volume.
What alloys can be Type II anodized?
Type II works well with 1000, 3000, 5000, and 6000 series aluminum alloys. ALBEI manufactures anodized coil in 1xxx, 3xxx, 5xxx, and 6xxx series. Higher alloy grades (such as 2xxx and 7xxx series with high copper or zinc content) are more challenging to anodize uniformly and are generally not recommended for decorative Type II applications.
What colors are available with Type II anodizing?
Class 1 (non-dyed) gives a clear/natural finish that shows the raw aluminum appearance. Class 2 (dyed) is available in black, bronze, champagne, gold, red, blue, and custom shades matched to customer color samples. The porous oxide structure accepts both organic and inorganic dyes, and the color is locked in during the sealing step for long-term durability.
Why is Type II used for coil anodizing?
Type II's room-temperature bath conditions, moderate film thickness (compatible with post-anodizing forming), excellent dyeability, and low cost make it ideal for high-volume continuous coil production. Unlike Type III which requires freezing baths and produces coatings too thick for forming, or Type I which uses environmentally restricted chromic acid, Type II hits the optimal balance for coil-to-coil manufacturing.
Get Started

Need Type II Anodized Aluminum?

ALBEI manufactures continuous coil-anodized aluminum with Type II sulfuric acid process. Custom alloys, thicknesses, colors, and finishes available.